Weekly meeting on MDC readout upgrade

-- BurkhardKolb - 25 Aug 2009

Participants:

BurkhardKolb, JanMichel, JoernWuestenfeld, AttilioTarantola, JoachimStroth, KathrinGoebel

Kathrins report

  • see pdf with measurements 1 to 8 boards.
  • one noisy board (b) was found
  • the other boards were all below 1 permille when adjusting the thresholds to about 50 (no individual tuning)
  • looks good
  • still needed is the CTS measurement
  • report to Christian and decision!

Jans report

  • all OEP Voltages were measured by the internal ADCs
  • look good with some exceptions were tuning/calibration of the ADC is required ( voltage divider).

Current measurements

  • see first measurements here: MdcAddonCooperation
  • proposal to make test with pulser firing all (or half of all) channels, then increase rate from 1 to 20 kHz (with reasonable thresholds)
  • check rise of current (should stay below 1 A for long MBO)
  • last OEP design leaves uninitialzed MBO at low current
  • there are doubts that the threshold setting worked, has to be checked with proper init file script.

Voltage distribution board/ Fanpw2

  • first board exists and is tested by Torsten
  • changing return currents ( from 5V) influence ground for 3+-3V on daughterboards because they are unregulated on the OEP
    • solution 1: new OEP with regulation for +-3 V (problem: neg low power LDOs not available)
    • solution 2 (favoured): common ground cable: make test with massive copper ground cable
  • Fanpw3 will be done ( 3 months )

latest tests in the cave

  • with 8 OEPBs and daq was done successfully

Unpacker

  • work has started including init from DB
  • Joern will come to GSI mid July to work with Ilse and Attilio
  • link to DataStructure
  • link to OEPNetworkAddresses
  • Michael will provide perl script for daq-anal, sniff, decode...
  • see first tests
  • done

Topics

  • It works - but
  • transfer too slow (FPGA to TRB?)
    • at GSI it runs with 75kHz
    • what's wrong at FZD?
    • no news yet
  • edge triggered data reception in FPGA
    • double and triple hits on same address, 0-hits
    • on all MBOs?
    • only on chains of 2 or more MBOs?
  • GDE signal derived from trigger, but MBO derived from CMS
    • GDE to late?
  • GDE release during calibration
    • reset hit registers to early?
    • data ok?
  • Make tests with pulser to measure electronics efficiency
  • new tests with pulser LVL1 up to 1MHz
  • high threshold with EB up to 20kHz - maybe the network with 10Mbits is the problem...
  • shielding - not clear if efficient, new residual plots needed
    • see FZR results (added by CM)
    • my (CM) interpretation of the recent results: NO significant change of the noise level, i cannot recommend to install these additional shieldings, also due to the unclear influence of the HV current, reported by Jörn.
  • charging up has to be investigated

decision on priority was taken

  • priority
    • 1. switch fast to OEP
    • (fix all errors on current design)

current work at GSI

  • Sector 4, layer 3 (POFs) and 4 started
  • all cables and POFs should be fixed to chamber, not to supports
  • new cable type for Common Stop needed (Michael)
  • better labels needed (Kathrin)

OEP work

  • Attilio reported about bit shifts in the FPGA
    • problem with Lattice design software
    • is manufacturer contacted? yes
    • problem not yet understood
    • comes and goes
    • now has disappeared
  • one link is now working
    • with data and calibration triggers
    • short and long MBO working
    • data file with current data format needed
    • new data format (2 times in 1 32-bit word) not yet
  • Jan is working on a 16 link version
    • ID info of several OEPs read out on hub
    • 8 links seem to work
    • problems with place and route software when more than 8 ports are used.
    • send problematic design to Lattice for help
    • still bit errors in media interface, sometimes dependend on recompilation of design, sometimes intermittent in time.
  • patched TRB needed
  • power distribution board to be tested (Kathrin) (5V, +-3V, 1.4V, 3.5V)
  • power now supplied by Genesys power supplies
  • test in cave with CMS needed for general green light
  • LVDS CMS signal cabled up
  • cross talk can be seen up to a distance of about 5mm
  • watch out during cabling!!!
  • needs now realistic cabling with more MBOs
  • test in cave with 1 MBO and 1 OEPB was done, see pictures of noise TestsinCave
  • qfile_009.tif: noise on analog readout during readout
  • qfile_010.tif: noise on analog readout during readout
  • qfile_011.tif: noise on analog readout during readout
  • readout test was running whole night through
  • agreement was reached on the possibility to switch between two different compression formats for debugging
  • work starts now (SY) to get it in standard readout to HLD-files

New transmission problem 21. July

  • Attilio reworked the FPGA code to support debugging
  • sometimes empty events with some wordcount are sent
  • problem seems to be in sending part
  • has to be solved until next week
  • solved

How to load thresholds and firmware

  • manipulate threshold in Oracle, output to files
  • automatic load via TRBnet to TDCs
  • take threshold data from FPGA after update and insert into data stream?

efficiency measurements at FZD

  • starts at 1900V (plateau), not understood yet, maybe gas mixture?
  • try out Argon isobutan mix
  • change gas flow (oxygen?)
  • small gas leaks are fixed, but no significant improvement at 60/40 mix
  • plateau at 1650 with 80/20 mix, see efficiency plateau
  • new measurements with gas flow switched off indicate leakage and contamination (oxygen) when flow is too low
  • He leak detection will be performed again
  • O2 measurements at FZD, manual available now
  • electrolyte cell was empty
  • needs new evaluation

Topic attachments
I Attachment Action Size Date Who Comment
CellvsT1_s2m0l0.jpgjpg CellvsT1_s2m0l0.jpg manage 43.6 K 31 Mar 2009 - 10:49 JoernWuestenfeld Cell vs. Time1 for layer0
CellvsT1_s2m0l1.jpgjpg CellvsT1_s2m0l1.jpg manage 37.8 K 31 Mar 2009 - 10:50 JoernWuestenfeld Cell vs. time1 for layer1
CellvsT1_s2m0l2.jpgjpg CellvsT1_s2m0l2.jpg manage 41.4 K 31 Mar 2009 - 10:50 JoernWuestenfeld Cell vs. time1 for layer 2
CellvsT1_s2m0l3.jpgjpg CellvsT1_s2m0l3.jpg manage 43.6 K 31 Mar 2009 - 10:50 JoernWuestenfeld Cell vs. time1 for layer3
CellvsT1_s2m0l4.jpgjpg CellvsT1_s2m0l4.jpg manage 42.7 K 31 Mar 2009 - 10:51 JoernWuestenfeld Cell vs. time1 for layer4
CellvsT1_s2m0l5.jpgjpg CellvsT1_s2m0l5.jpg manage 46.1 K 31 Mar 2009 - 10:51 JoernWuestenfeld Cell vs. time1 for layer5
Efficency.jpgjpg Efficency.jpg manage 36.5 K 20 Apr 2009 - 07:00 JoernWuestenfeld Efficency of variouse gas mixtures and flows
MB-Shielding-FZR.jpgjpg MB-Shielding-FZR.jpg manage 42.8 K 28 Apr 2009 - 15:29 ChristianMuentz MB Shielding
MDC-TRB-dataword01.pdfpdf MDC-TRB-dataword01.pdf manage 23.7 K 20 Apr 2009 - 12:49 JoernWuestenfeld MDC dataword comparison SAM -> OEP
MDC_DAQ_txtEXT MDC_DAQ_txt manage 1.4 K 04 Aug 2009 - 06:45 JoernWuestenfeld Mail from Sergey
MdcGas.jpgjpg MdcGas.jpg manage 95.0 K 21 Apr 2009 - 09:40 ChristianMuentz # of cluster He/Isob Ar/Isob
Noise.pdfpdf Noise.pdf manage 15.0 K 22 Apr 2009 - 09:06 JoernWuestenfeld Comparing absolute Noise distributions
NoiseComparison.pdfpdf NoiseComparison.pdf manage 105.4 K 06 Apr 2009 - 06:45 JoernWuestenfeld Compairing noise situation with and without MBO shielding.
Normalized.jpgjpg Normalized.jpg manage 46.9 K 20 Apr 2009 - 07:00 JoernWuestenfeld Efficency normalized to coincidence countrate and fitted with fermi function
PresentationOcc2009-08-25.pdfpdf PresentationOcc2009-08-25.pdf manage 214.8 K 25 Aug 2009 - 10:56 KathrinGoebel Occ measurents 2009-08-25
efficencyPlateau.jpgjpg efficencyPlateau.jpg manage 31.1 K 07 Apr 2009 - 13:00 JoernWuestenfeld Plateau curve of efficency
event_oep.txttxt event_oep.txt manage 0.7 K 18 Aug 2009 - 09:10 JoernWuestenfeld Event dump with 8 OEP's
gasdep.jpgjpg gasdep.jpg manage 31.2 K 21 Apr 2009 - 10:50 JoernWuestenfeld gas dependency plot
noise_213-216313314_thr30.pdfpdf noise_213-216313314_thr30.pdf manage 13.2 K 18 Aug 2009 - 06:14 JoernWuestenfeld Noise picture from 8 MBO's
noise_213_thr30.pdfpdf noise_213_thr30.pdf manage 13.1 K 18 Aug 2009 - 06:13 JoernWuestenfeld Noise picture from one MBO
noisedifference.jpgjpg noisedifference.jpg manage 25.2 K 22 Apr 2009 - 09:06 JoernWuestenfeld Difference in Noise between shielded and unshielded MBO's
overview_occ_140809.pdfpdf overview_occ_140809.pdf manage 6.1 K 18 Aug 2009 - 10:29 KathrinGoebel Dataword Occ, 14.08.2009, work in progress
overview_occ_140809_zoom.pdfpdf overview_occ_140809_zoom.pdf manage 6.0 K 18 Aug 2009 - 10:30 KathrinGoebel Dataword Occ Detail, 14.08.2009, work in progress
qfile_009.tiftif qfile_009.tif manage 14.1 K 16 Jun 2009 - 11:19 BurkhardKolb noise on analog readout during readout
qfile_010.tiftif qfile_010.tif manage 12.7 K 16 Jun 2009 - 11:19 BurkhardKolb noise on analog readout during readout
qfile_011.tiftif qfile_011.tif manage 15.3 K 16 Jun 2009 - 11:20 BurkhardKolb noise on analog readout during readout
streamer_tubes_nima_1982_Seite_04_a.jpgjpg streamer_tubes_nima_1982_Seite_04_a.jpg manage 61.8 K 21 Apr 2009 - 06:17 LotharNaumann Ar/isobuthan dependend working characteristics
voltages_200908211552.txttxt voltages_200908211552.txt manage 2.2 K 25 Aug 2009 - 10:56 KathrinGoebel voltages for occ measurements
Edit | Attach | Print version | History: r45 | r43 < r42 < r41 < r40 | Backlinks | View wiki text | Edit WikiText | More topic actions...
Topic revision: r42 - 25 Aug 2009, BurkhardKolb
 
This site is powered by FoswikiCopyright © by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding Hades Wiki? Send feedback
Imprint (in German)
Privacy Policy (in German)