Open Tasks

Tasks currently on our agenda:

• Remove obsolete cables - still a topic (Everybody who is familiar with the old setup)
• Install temperature sensors for RICH power supplies
• Re-Install MDC Analog Out connection to Counting House (Erwin)
• Add fans where missing
• Install trigger cables TOF-MDC34
• Install trigger cables for RPC (Alberto)
• Install trigger cables for Forward Wall
• Adjust all FanPW to final settings
• Connect power for RPC switches
• Install RPC Hadcon (Alberto)
• MDC - what is missing?

Logbook

18.01.2010

• Put cables and filters on 10 more new fans (Joern, Jan)
• Prepare RPC / Shower trigger cables (Gosia)
• Lay 48V distribution for TRBs MDC12 RICH (Torsten)
• Lay 48V distribution for TRBs left front (Torsten)
• Lay 48V distribution for TRBs right front (Torsten)
• Lay Optical cables left front corner (Jan)
• Finish TOF TRB stacks (Joern, Jan)
• Finish MDC1 sector 4 cables (Gosia, Joern)
• Find and install available network switches (Sergey)

19.01.2010

• removed power cables for RICH (Joern, Khaled, Jan)
• Prepare more 50cm power cables (Khaled, Gosia, Joern)
• Add filters for Fans where missing (Joern)
• Lay 48V distribution for RPC TRB (Torsten)
• Lay 48V distribution for RPC (Torsten)
• Prepared optical cables for MDC 1/2 (Gosia, Joern, Torsten, Jan)
• Loaded new kernels on many trbs (Sergey)

20.01.2010

• Made list of available temperature sensors for MDC1/2 (Khaled)
• Soldered new temperature sensors (Erik)
• Removed RICH power cable to tent (Erwin)
• Installed front left and rear right TRB stacks (Andreas)
• Installed final Ethernet setup for all three corners of the mainframe (Sergey, Jan)
• Changed stack for CTS (Jan)
• Continued tests for MDC (Gosia, Joern)
• Fixed some mistakes on sector 3 plane 3/4 (Gosia, Erwin)

22.01.2010

• Layed all optical cables for rear right, front right corner and MDC1/2 / RICH to optical switches, Ethernet switches and CTS (Joern, Erwin, Jan)
• Installed TRB mountings (Andreas)
• Mounted TRB stacks (Joern, Andreas, Jan)
• Soldered trigger distributor boards (Gabi)
• Soldered all temperature sensors for MDC plane 3&4 (Erik, Gosia)
• Mounted trigger distributor on TRB stacks (Gosia)
• Removed MDC Analog Out Cables between Patch panels - has to be redone in a better way (Joern, Erwin)
• Removed LEMO cables on MDC rack

26.01.2010

• Lay 48V distribution for TRBs right rear (Torsten)
• Build holding for optical switches (Andreas)
• Installed and connected optical switches for MDC1/2 & RICH (Jan)
• Changed RPC stacks on sector 3 & 5 to final setup (Yurek, Jan)
• Equipped one more RPC stack (Marek, Jan)
• Prepared power cables for Trigger distributor board (Jan)

27.01.2010

• Prepared two new trigger cables for RPC (Kathrin)
• Change power supply for RPC to final setup (Torsten, Jan)

28.01.2010

• The last three stacks prepared for RPC (Marek, Sergey)

29.01.2010

• Prepared six TRB stacks for TOF with Power distributor (Erik)
• Installed two network switches in rear right corner, including cables (Jan)
• Labeled most of RPC cables individually (Kathrin)
• Layed trigger cable (17pair) from CTS to both TOF/MDC34 and RPC/Shower / corner of mainframe (Erwin, Jan)
• Prepared more 50cm 48V cables (Paul)
• Put RJ45 connectors on PCB for temperature sensors (Paul, Erik)
• Started removing temporary RPC setup (Jan)

01.02.2010

• Removed all temporary RPC setups
• Uninstalled LV power supplies for making changes
• Put cables for TOF on sector 3
• Prepared cables for RPC / Shower to be put into new cable chains.

03.02.2010

• Three stacks of RPC TRBs successfully tested (CTS, old HUB, readout) and ready for mounting (Marek, Sergey)

09.02.2010

• Installed cable guide on rear corners (Torsten, Andreas, Jan)
• Continued with TOF cables (Erwin)

18.02.2010

• Two stacks with TRBs for RPC built and tested (CTS, old HUB, readout) and ready for mounting (Marek, Sergey)

19.02.2010

• Four TRBs for TOF tested (CTS, old HUB, readout) and ready for mounting (Marek, Sergey)

22.02.2010 (and before)

• Install new cable guides to RPC/Shower
• Soldered temperature sensor hub boards
• Soldered CTS trigger fanout boards
• Finished testing & labelling half of temperature sensors for MDC 3/4
• Lay all DAQ cables to each RPC/Shower sector (1x trigger, 6x optical cable, 1x Ethernet, 1x Temp.Sens. 2x CAN)

07.05.2010

• Installed Forward Wall Hub
• Changed trigger setup according to Michael's mail

-- JanMichel - 29 Jan 2010